How To Install Carpet Stair Tread Pads

Add a touch of elegance, texture and colour to your domicile's interior staircase by installing a carpeting runner. The narrow strip of rug is set on a pad and then attached to tackless strips nailed to each tread. The thin, dumbo pad helps to quiet and cushion footsteps, but it also prevents the runner from wearing out prematurely. Don't use standard foam padding; information technology'southward too soft to provide the necessary support.

Installing a stair runner on a directly staircase is a relatively easy projection, even for novice do-it-yourselfers. Winder stairs that turn corners are more challenging, just still achievable with our expert instructions.

Stair runners are priced by the linear pes, and available in two widths: 27 inches and 32 inches. They're made of synthetic fibers, wool, or a combination of both. Visit a carpeting outlet to see samples of the patterns and colors available.

Installing Carpet Runner on Stairs Overview

Gregory Nemec

How to Install Stair Rug Runner

1. Laying out tackless strips for a stair runner

Photo by Rebecca Cinclair

• Subtract the width of the runner from the width of the staircase (between baluster and skirtboard) and carve up by two.
• Lightly marking that distance out from the skirtboard and from the balusters on every tread where it meets the riser.
• For each tread, utilize canvas-metal snips to cut a tackless strip 2 inches shorter than the width of the runner. Be certain there's a nail within a couple of inches of each end.
• Place a scrap piece of strip flush against the riser. Center the cut strip—pins angled toward riser—between the layout marks. Butt it against the scrap and nail.

two. Fit carpet pad

Photo by Rebecca Cinclair

• Cutting rug pad the same width as the tackless strips and 3 inches longer than the depth of the tread.
• Butt pad to forepart edge of tackless strip. Fasten edge of pad to tread with nine⁄16-inch staples spaced every three inches.
• Pull pad tight around nosing and staple every iii inches into underside of nosing.
• Cut pad where nosing and peak of riser see.

Tip: When using the waterfall method, clip 3 inches off the corners of the pad where it curves around the nosing. This helps hide the pad.

3. Secure runner to commencement riser

Photograph by Rebecca Cinclair

• Check terminate of runner with framing square. If non square, mark, then cut along bankroll with carpet knife. Dab cut edges with latex carpet mucilage to preclude fraying.
• After glue dries to bear upon, unroll runner up 3 or iv treads, making sure information technology's between the layout marks.
• Push button end of runner confronting flooring at lesser of showtime riser. Line up runner betwixt the layout marks.
• Staple cease of runner to lesser of riser every iii inches.

Tip: Push stapler through the pile and against the backing before pulling trigger.

four. Attach runner to treads

Photo by Rebecca Cinclair

• Line upwardly runner between layout marks on kickoff tread. Push it hand-tight toward tackless strip.
• Identify front edge of genu kicker on center of the runner near 2 inches from the riser. Concur downward front knob with ane hand, using the other mitt to keep the kicker'southward shaft level.
• Hit kicker with articulatio genus. Runner should engage tackless strip and become taut. Repeat every 3 inches, side to side.

Tip: If runner bulges and doesn't lie flat against the tread, lift it direct upward off the strip and brainstorm again.

five. Fasten runner to riser

Photo past Rebecca Cinclair

• Use carpet tool and rubber mallet to pack runner tightly between the tackless strip and the riser.
• Nigh both ends of the tackless strip, staple the runner into the crease where riser meets tread.
• Staple each border of the runner 2 inches above lesser of riser. (For upholstered installation, staple edges to riser, and then staple runner to underside of nosing every iii inches.)
• Repeat Steps 3 and 4 up to last riser.
• At summit of final riser, cutting runner tight to the underside of the nosing or molding. Dab edges and stop with glue and staple into top of riser and along edges every 3 inches.

Tip: Staple rug directly to stairs, never through the pad.

vi. Install rods (optional)

Photo by Rebecca Cinclair

• Attach finials (if any) to outside of each rod subclass.
• Place a subclass confronting either edge of the runner at the intersection of the tread and riser.
• Hold them in place and mark the locations of the spiral holes. Drill 1⁄16-inch pilot holes at each mark.
• Screw each bracket to tread and riser.
• Marker and cut rods to length with a tubing cutter or hacksaw.
• Printing rod into pucker where tread and riser meet. Secure both ends in the brackets.

---

Tools

Source: https://www.thisoldhouse.com/stairs/21016683/how-to-install-a-handsome-stair-runner

Posted by: townsendmosis1960.blogspot.com

Share this post